![KIDKRAFT AINSLEY F26415E INSTALLATION AND OPERATING INSTRUCTIONS MANUAL Pdf Download (1) KIDKRAFT AINSLEY F26415E INSTALLATION AND OPERATING INSTRUCTIONS MANUAL Pdf Download (1)](https://i0.wp.com/static-data2.manualslib.com/product-images/dc7/2036993/kidkraft-ainsley-f26415e.jpg)
- Manuals
- Brands
- KidKraft Manuals
- AINSLEY F26415E
- Installation and operating instructions manual
Hide thumbs
-
- Contents
- Table of Contents
- Bookmarks
Table of Contents
-
Table of Contents
-
Warnings and Safe Play Instructions
-
Protective Surfacing Guidelines
-
Instructions for Proper Maintenance
-
About Our Wood - Limited Warranty
-
Keys to Assembly Success
-
Keys to Assembly Success
-
Part ID
-
Part ID
-
Step-By-Step Instructions
Advertisem*nt
Quick Links
- 1 Table of Contents
- 2 Step-By-Step Instructions
- Download this manual
AINSLEY
A INSLEY
OUTDOOR
PLAY
CLIMBING
SYSTEM
FRAME-FSC
F24145
F26415E
INSTALLATION AND OPERATING INSTRUCTIONS
INSTALLATION AND OPERATING INSTRUCTIONS
WARNING
them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 22'-3" x 28' x 13'-10" area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6'(1.8m)
CAPACITY - 6 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for domestic use.
KidKraft, Inc.
KidKraft, Inc.
4630 Olin Road
4630 Olin Road
Dallas, Texas 75244 USA
Dallas, Texas 75244 USA
customerservice@kidkraft.com
customerservice@kidkraft.com
canadacustomerservice@kidkraft.com
canadacustomerservice@kidkraft.com
1.800.933.0771
1.800.933.0771
972.385.0100
972.385.0100
For online parts replacement visit
For online parts replacement visit
https://parts.kidkraft.com/
https://parts.kidkraft.com/
WARNING
To reduce the risk of serious injury or death, you must read and follow
these instructions. Keep and refer to these instructions often and give
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 22'3" x 28' area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6' (1.8 m)
CAPACITY - 6 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for domestic use.
KidKraft Netherlands BV
KidKraft Netherlands BV
Olympisch Stadion 8
Olympisch Stadion 8
1076 DE Amsterdam
1076 DE Amsterdam
The Netherlands
The Netherlands
europecustomerservice@kidkraft.com
europecustomerservice@kidkraft.com
+31 20 305 8620 M-F from 09:00 to 17:30
+31 20 305 8620 M-F from 09:00 to 17:30
(GMT+1)
(GMT+1)
For online parts replacement visit
For online parts replacement visit
https://parts.kidkraft.eu/
https://parts.kidkraft.eu/
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often
9'
Table of Contents
Table of Contents
Warnings and Safe Play Instructions . . . . . . . . . . . . . . pg. 2
Warnings and Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines . . . . . . . . . . . . . . . . . . pg. 3
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions for Proper Maintenance . . . . . . . . . . . . . . . pg. 4
Instructions for Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood - Limited Warranty . . . . . . . . . . . . pg. 5-6
About Our Wood - Limited Warranty . . . . . . . . . . . . . . pg. 5
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 7
Keys to Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 6
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 9
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 7
Step-By-Step Instructions . . . . . . . . . . . . . . . . . . . . . . pg. 14
Installation of I.D./Warning Plaque . . . . . . . . . . . .Final Step
Installation of I.D./Warning Plaque . . . . . . . . . . . . . . . pg.56
9404145
9404415E
22' 3"
10' 3"
28'
7' 10"
4 - 8 Hrs
Two person
assembly
4 - 8 Hrs
Two person
assembly
Rev 07/03/2020
Rev 03/05/2021
Advertisem*nt
Table of Contents
Related Manuals for KidKraft AINSLEY F26415E
-
Ainsley play system (72 pages)
-
(58 pages)
-
Falcon ridge playset (106 pages)
-
(102 pages)
-
(78 pages)
-
Play system (101 pages)
-
(101 pages)
-
(120 pages)
-
(76 pages)
-
(48 pages)
-
(80 pages)
-
(80 pages)
-
(85 pages)
-
(100 pages)
-
(92 pages)
-
(104 pages)
Summary of Contents for KidKraft AINSLEY F26415E
-
Page 1: Table Of Contents
Protective Surfacing Guidelines ....pg. 3 Protective Surfacing Guidelines....pg. 3 KidKraft, Inc. KidKraft Netherlands BV KidKraft, Inc. KidKraft Netherlands BV Instructions for Proper Maintenance . -
Page 2: Warnings And Safe Play Instructions
Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system. -
Page 3: Protective Surfacing Guidelines
Protective Surfacing - Reducing Risk of Serious Head Injury From Falls One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292. -
Page 4: Instructions For Proper Maintenance
Instructions for Proper Maintenance Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it. -
Page 5: About Our Wood - Limited Warranty
About Our Wood KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set. -
Page 6: Keys To Assembly Success
KidKraft Limited Warranty MISSING OR DAMAGED PARTS: KidKraft will replace any parts within 90 days from date of purchase found to be missing from or damaged in the original packaging. See Fig.1 Fig. 1 Product Age (All Parts) Consumer Pays... -
Page 7: Keys To Assembly Success
Keys to Assembly Success Tools Required • Tape Measure • #1 Phillips, #2 Robertson • Open End Wrench • 3/16”(5mm) Hex Key • Carpenters Level and Screwdriver 1/2” (13mm) & 9/16”(14 mm) • 8’ (2.4m) Step Ladder • Carpenters Square •... - Page 8 Your Key To Quick Assembly SORTING WOOD PARTS INTO EACH ASSEMBLY STEP WILL SAVE TIME! Step Step Step SAVE TIME - TIP #1: Open each box with wood parts and look for the Key Number stamped on the end of the wood part (see chart below). Sort each wood part into the different assembly steps.
-
Page 9: Part Id
Part Identification WOOD CHART 1 x 4 x 32-1/2" - 0304 3630304 ⅜ ⅜ ⅜ ⅜ 2 x 6 x 69-1/2" - 1772 3631772 ⅜ ⅜ ⅜ 2 x 6 x 69-1/2" - 1773 3631773 1 x 6 x 23-1/2" - 1774 3631774 1 x 6 x 23-1/2"... - Page 10 Part Identification (Reduced Part Size) WOOD CHART 1 x 2 x 26-7/8" - 1750 3641750 ⅜ ⅜ ⅜ ⅜ 2 x 2 x 38" - 1751 3641751 ⅜ 1 x 4 x 38-1/2" - 1752 3641752 ⅜ ⅜ 1 x 4 x 26-7/8" - 1753 3641753 1 x 4 x 31-1/2"...
- Page 11 Part Identification (Reduced Part Size) Part Identification (Reduced Part Size) 5/4 x 2 x 38-1/2" - 1763 3641763 5/4 x 2 x 38-1/2" - 1763 3641763 2 x 3 x 38-1/2" - 1764 3641764 2 x 3 x 38-1/2" - 1764 3641764 2 x 3 x 42-3/4"...
- Page 12 Hardware Identification - 9274211 (LW1, FW1, TN1) - 9277212 (LW1, FW1, TN1) - 9277220 (LW1, FW1, TN1) - 9277222 (LW1, FW1, TN1) - 9277242 (LW1, FW1, TN1) 1/4 x 4 3/4" - 9277243 (LW1, FW1, TN1) - 9277252 (LW1, FW1, TN1) - 9277241 (LW1, FW1, TN1) (1) 1/4 x 2 3/4"...
- Page 13 Hardware Identification (Actual Size) 9277320 1x - D4 - #2 x 2"(50.8mm) - 9200014 (2) 5/16 x 2" (2 x FW2, LN2) 9262230 (3) 1/4 x 3" - FW1 (24) #8 x 1 1/8" (52042514) (18) #8 FW3 (9251500) (59) #8 x 1 1/2" (52042512) (12) #8 x 2 1/2"...
-
Page 14: Step-By-Step Instructions
Before you discard your cartons fill out the form below. • The carton I.D. stamp is located on the end of each carton. The tracking number is located on the KidKraft ID Plaque (9320371). • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department. - Page 15 Step 2A Hex Bolt Assembly Warning: For your childs safety, Lock T-Nut Washer orientate the swing hangers as shown to ensure your swing will have proper swing motion when Flat Bolt Washer installed. Failure to do so could result in premature failure of the swing hanger or swing chain.
- Page 16 hammer, 1/2" wrench Step 2B Step 1b: Swing Beam Assembly icon 4X G1 (FW2, LW2, TN2) 1773 Note: Install T-Nuts first! Important! Fort End Side (Triangle Plate Does NOTE: Interior hole is Not Overhang) used for these ends. 1772 SW Beam Front 1773 SW Beam Front 3200184 3200184...
- Page 17 Step 3 Hex Bolt Assembly Lock T-Nut Washer Flat Bolt Washer Note: Install T-Nuts first! 1755 1749 1756 1749 Hardware Wood Parts 5/16 x 4” 2 x 4 x 79-1/2” 1749 (FW2, LW2, TN2) 2 x 4 x 44” 1756 5/16 x 4-1/2”...
- Page 18 Step 4 hammer, 7/16" socket, 1/2" wrench Step 3: Swing Beam Assembly icon 1X H2 (LW1, FW1, TN1) 1x G5 (LW2, FW2, TN2) 1x G8 (FW2 x2, TN2) Notes: -Install T-Nuts first! 4919 1772 1773 Side with Overhang Hardware Wood Parts 1/4 x 4-1/4”...
- Page 19 Notes: Step 5A -Install T-Nuts first! -Keep bolts loose until next step. -Make sure assembly is square. Hex Bolt Assembly Lock T-Nut Washer Notes: - Install T-Nuts first! Flat Bolt Washer - Keep bolts loose until next step. - Make sure assembly is square. 1771 1771 1759...
- Page 20 Step 4b: Swing Side Assembly icon Step 4b: Swing Side Assembly icon Step 5B 3X H2 (LW1, FW1, TN1) 3X H2 (LW1, FW1, TN1) 1X LS3 (FW1) 1X LS3 (FW1) Notes: Predrill Pilot Holes for Lag Screw Notes: Hex Bolt Assembly Note: Pre-drill all holes using -Install T-Nuts first! Lock...
- Page 21 hammer, 1/2" socket Step 4c: Swing Side Assembly icon Step 5C 2X G4 (LW2, FW2, TN2) Notes: -Install T-Nuts first! Notes: - Install T-Nuts first! 1757 1757 Hardware Wood Parts 2 x 4 x 40-3/4” 5/16 x 4” 1757 (LW2, FW2, TN2)
- Page 22 hammer, 7/16" socket Step 5a: Wall Side Assembly icon Step 6A 10X H2 (LW1, FW1, TN1) Notes: -Install T-Nuts first! -Make sure assembly is square. 1753 Back 1760 11 3/4” Notice hole (298.5 mm 1771 towards back 1771 1769 1753 1760 1771 1771...
- Page 23 Step 5b: Wall Side Assembly Step 6B 2X S2 1769 FLUSH 1766 1769 NOTE: Use the side without the holes 1766 Wood Parts Hardware 2 x 3 x 4-1/2” 1766 #8 x 1-1/2”...
- Page 24 hammer, 7/16" socket Step 7 Step 6: Front Frame Assembly icon 2X H6 (LW1, FW1, TN1) Flush 4x S7 (FW0) Notes: -Install T-Nuts first! 1752 FRONT 1752 Notice hole towards top 1764 Notice hole towards bottom 1764 Wood Parts Hardware 2 x 3 x 38-1/2”...
- Page 25 Step 8A Step 7a: Rock Rail Assembly 2X S3 1765 1766 FLUSH 1/2" 12.7 Hardware Wood Parts #8 x 2-1/2” 2 x 3 x 4-1/2” 1766 2 x 3 x 42-3/4” 1765...
- Page 26 Step 7b: Rock Rail Assembly Step 8B 2X S15 2x S2 FLUSH FRONT Hardware #8 x 1-1/2” #8 x 1-3/4”...
- Page 27 hammer Step 8: Attach Centre Divider icon Step 9 1x H2 (LW1, FW1, TN1) 1x H11 (LW1, FW1, TN1) Note: Install T-Nuts first! 1751 1751 1751 1764 Wood Parts Hardware 2 x 2 x 38” 1751 1/4 x 2” (LW1, FW1, TN1) 1/4 x 2-3/4”...
- Page 28 Step 10 Step 9: Attach Gusset 4x S4 0312 FRONT 0312 0312 FLUSH Hardware Wood Parts #8 x 3” 2 x 3 x 16” 0312...
- Page 29 : Attach Lower Front Step 11 TOP HALF OF STRUCTURE HIDDEN FOR CLARITY 1767 1766 1767 1767 Hardware Wood Parts #8 x 1-3/4” 1 x 6 x 39-3/4” 1767...
- Page 30 hammer icon Step 11a: Floor Back Assembly Step 12A 2x S7 (FW0) 2x H3 (LW1, FW1, TN1) Note: Install T-Nuts first! 1761 1762 1761 1762 1761 1762 Hardware Wood Parts #12 x 2 (FW0) 2 x 2 x 34-3/4” 1761 5/4 x 4 x 38-5/8”...
- Page 31 hammer Step 12B Step 11b: Floor Back Assembly icon hammer 2x H5 (LW1, FW1, TN1) Step 11b: Floor Back Assembly icon 2x H5 (LW1, FW1, TN1) Note: Install T-Nuts first! Note: Install T-nuts first! Note: Install T-nuts first! 1762 FRONT FRONT Hole towards bottom 1762...
- Page 32 Step 11c: Floor Back Assembly Step 12C 2x LS3 (FW1) 2x S7 (FW0) Predrill Pilot Holes for Lag Screw Pre-drill all pilot holes using a Predrill 1/8” pilot hole 1/8” drill bit before installing the lag screws. Use factory drilled Step 11c: Floor Back Assembly hole as a guide 2x LS3 (FW1)
- Page 33 2x PB2 (LW1, FW1, TN1) 3x S5 (FW3) hammer Step 13A Step 12a: Chalk Wall Frame icon Note: -Install T-nuts first! 2x PB2 (LW1, FW1, TN1) -Keep bolts loose. Note: 3x S5 (FW3) - Install T-Nuts first! Tuck edges under - Keep bolts loose.
- Page 34 Step 13B Note: -Install T-nuts first! -Keep bolts loose. Note: - Install T-Nuts first! - Keep bolts loose. FRONT 0359 0359 0359 Chalk Wall Assembly Hardware 1/4 x 1-1/2” (LW1, FW1, TN1)
- Page 35 4x S7 (FW0) Step 12c: Chalk Wall Frame Step 13C 4x S7 (FW0) Note: -Make sure 1758 is level. -Tighten all bolts. Note: -Make sure 1758 is level. -Tighten all bolts. FRONT FRONT 1758 Hardware #12 x 2” (FW0)
- Page 36 Step 14A 1754 1754 3” (76.2mm) FRONT Wood Parts Hardware 1 x 4 x 31-1/2” #8 x 1-1/8 1754...
- Page 37 Step 14B FRONT Hardware #8 x 1/2 (FW3)
- Page 38 3x S5 (FW3) Step 14C FRONT Hardware #8 x 1/2 (FW3)
- Page 39 Step 15 Step 14: Floor Frame Assembly Step 14: Floor Frame Assembly Step 14: Floor Frame Assembly 2x S4 2x S4 2x S4 3" 3" 3" 76.5 3" (76.2mm) 76.5 76.5 1-3/8" (35 mm) 1763 1763 1763 FRONT FRONT FRONT Wood Parts Hardware 5/4 x 2 x 38-1/2”...
- Page 40 Step 16A Step 15a: Attach Floor Boards 10x S2 x 5 per board 1774 1774 1774 FRONT TOP VIEW FLUSH FLUSH FLUSH FLUSH 1774 1774 FRONT (1752 hidden for clarity) Hardware Wood Parts 10 x #8 x 1-1/2” 1 x 6 x 23-1/2” 1774...
- Page 41 Step 15b: Attach Floor Boards Step 16B Step 15b: Attach Floor Boards 25x S2 25x S2 x 5 per board 1776 1776 Do not attach screw in this step for this hole. FRONT Front FRONT TOP VIEW TOP VIEW FLUSH Flush TOP VIEW FLUSH...
- Page 42 Step 15c: Attach Floor Boards 2x S3 Step 16C Step 15c: Attach Floor Boards 2x S3 1766 Fig. 15.3 1764 Fig. 15.3 1766 1766 1764 1766 FRONT Hardware Wood Parts #8 x 2-1/2” 2 x 3 x 4-1/2” 1766 FRONT...
- Page 43 Step 17 Step 16: Attach Ground Stakes 4x S3 MOVE FORT TO FINAL LOCATION. MOVE FORT TO FINAL LOCATION. FINAL LOCATION MUST BE ON LEVEL GROUND FINAL LOCATION MUST BE ON LEVEL GROUND. WARNING: To prevent tipping and avoid potential WARNING: injury, stakes must be driven 10-1/2”...
- Page 44 Step 17: Wall Assembly Step 18 20x S1 3" [3"] TYP (76.2mm) 2 PLACES 2 Places 2 1/2” (63.5mm) [2 1/2"] TYP 4 Places 0304 4 PLACES 0304 0304 1" 1” 25.6 (25.4mm) 5 Places 5 Places FRONT Wood Parts Hardware 1 x 4 x 32-1/2”...
- Page 45 Step 19A 3391267 9750140 9750140 1750 3391267 Other Parts Wood Parts 1 x 9750140 1 x 2 x 26-7/8” 1750 2 x 3391267 (2 pk)
- Page 46 Step 18b: Canopy Roof Assembly cont. 16x S10 Step 19B 5/8" 15.8 Step 18b: Canopy Roof Assembly cont. Note: Use tube holder as a guide to pre-drill holes with 16x S10 1/8" bit. Note: Use tube holder as a guide to pre-drill holes with 1/8” bit. 5/8”...
- Page 47 Step 19C Step 18c: Canopy Roof Assembly cont.
- Page 48 Step 19D Hardware #8 x 1/2” (FW3)
- Page 49 Step 20A Note: Upper half of structure removed for clarity. 1765 1765 1765 Wood Parts Hardware 2 x 3 x 42-3/4” 1765 #8 x 1-3/4”...
- Page 50 Step 19b: Rock Ladder cont. Step 20B Step 19b: Rock Ladder cont. 20X S2 20X S2 FLUSH FLUSH FLUSH FLUSH 2" 2” 2" (50.8mm) 50.4 TYP 50.4 TYP 4 PLACES 4 PLACES 4 Places x 4 per board Note Hole Note Hole Orientation Orientation...
- Page 51 Barrel Nut, & Pan Screw included in bag hammer Step 19c: Rock Ladder cont. icon Step 20C Pan Bolt, Lock Washer, Flat Washer, Barrel Nut, & Pan Screw included in bag Note: Upper half of structure removed for clarity. Note: Upper half of structure removed for clarity.
- Page 52 Note: -Place slide in opening. -Pre-drill all holes using Step 21 1/8" drill 1/8" drill bit before tach Slide icon installing screws. - Rest of structure Note: removed for clarity. slide in opening. - Place slide in opening. ill all holes using - Pre-drill all holes using 1/8”...
- Page 53 Step 22 hammer, 1/2" socket Step 21: Attach Swing To Fort icon Note: Install T-nuts first! Note: Install T-nuts first! 1757 Hardware 5/16 x 4-1/2” Hex Bolt (LW2, FW2, TN2) 5/16 x 2” Hex Bolt (FW2 x2, TN2) Hardware 5/16 x 4-1/2” (LW2, FW2, TN2) 5/16 x 2”...
- Page 54 Step 23 WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2” into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. 0318 10-1/2” (266.7mm) Wood Parts Hardware 1 1/4 x 1 1/2 x 14”...
- Page 55 Step 23: Attach Swings Step 24 Step 23: Attach Swings A: Insert flexible Swing Hanger Cover over hook. (fig. 23.1) A: Insert flexible Swing Hanger Cover over hook. (Fig. 24.1) A: Insert flexible Swing Hanger Cover over hook. (fig. 23.1) B: Slide Swing Hanger Cover around hook until at top.
- Page 56 Final Step: Attach I.D. Plaque ATTACH THIS WARNING & I.D. PLAQUE TO A PROMINENT LOCATION ON YOUR PLAY EQUIPMENT! (Fort or Swing Post) This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model.
- Page 57 NOTES...
- Page 58 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft Netherlands BV https://prdregistration.kidkraft.com/ Olympisch Stadion 8 1076 DE Amsterdam The Netherlands KidKraft would like to say Thank You for Attention: Customer Service your time and feedback.